Estate E-S 1600 Bedienerhandbuch

Instruction Manual for the Manufactured by E-SC 1600 / E-SC 1602 Series

Manual Operation Mode Manual operation mode will be necessary to learn from installation and programming. It is also useful for emergency situations w

IMPORTANT: Determining Correct Setback 3.1 PULL TO OPEN - Standard operation. This means the gate operator is mounted on the inside of the property a

Installation of Operator The operator base plate and articulated arm are designed either for right-handed or left-handed installation. 1. Begin with

4. Assemble the articulated arm and front coupling as shown below. Left assembly connects the same way as the right only with the straight arm and ga

Mounting the Control Board and Box 1. Position your control box on the post of the gate or a near by fence. Remove the rubber cov-ers on the back of

Positioning Backup Batteries 1. Slide the two batteries below the control board mount. They do not require any additional bracing. Create holes on

4.3 For Your Convenience The white terminal strips on the control board are easily removed for wiring. Simply pull straight out on the terminal strip

Installation of Limit Switches and Positive Stops Positive stops are physical structures the gate comes in contact with at the end of the opening and

4.5 Wiring the Limit Switches On the limit switch: • 1 is Common • 2 is N/C Limit Connection • 4 is not used Example of how to tighten the limit

Temporary Safety Jumpers For the highest level of safety, the Estate Swing systems are set up with Normally Closed safety terminals. This means that

CE DECLARATION OF CONFORMITY OF MACHINES (Directive 89/392/EEC, Annex II, Part B) Manufacturer: FAAC S.p.A. Address: Via Benini, 1 – 40069 Zola Pred

Wiring The Operator Arm(s) For the Master Operator: In terminal block CN2 insert the blue wire in APM1 and brown wire in CHM1. For the Slave Operator

4.8 Installing and Setting Transmitters and Receivers Installing the Receiver 1) Locate the 5 Silver Pins in the lower right hand corner of the Esta

4.9 Power 1. The Estate Swing E-SC 1600 comes with 1) 24V transformer. The transformer supplied has 2 screw terminals to connect to. You may locate t

Setting Operating Parameters Complete this step prior to programming the gate run time. This will dictate how your gate will react during programming

Operating Parameters Chart Minimum Force Medium-low Force Medium-high Force High Force This parameter adjusts the sensitivity of the electronic clu

20% of total arch 10% of total arch SOFT START/STOP This parameter determines when the gate will begin to slow down near the end of opening and closi

Programming Gate Run Times In this stage, your control board will memorize where your limits are (identified by limit switches, positive stops or both

5. When the closing stop point or limit switch is reached, the motor pauses for approximately 2 seconds, and then restarts with a total opening maneuv

Control Board LED Lights - The control board LED lights are located above their respec-tive terminals that they represent. (With exception of ALIM, po

6.2 Troubleshooting If the gate opener will not move. Be sure you have gone through programming. Without programming no power is ever sent to the op

Estate Swing Summery of Functions The Estate Swing is only to be used for vehicular swing gates in a Class I setting. Class I: A vehicular gate open

6.3 If fuse the F2 fuse blows or continues to blow. Check all wiring to both the backup batteries and to all accessories run off of the 24+,- termina

6.4 If you call in for technical support or warranty sup-port: before any control board or motor will be per-mitted to be sent in for testing or warra

Control Board Overview 7.1 Caution! Do not run 110V AC power direct to the board. This will cause permanent damage to both boards and void your warran

CN2 - Located on the lower left side of the board, these terminals are outputs for the opera-tor arm(s), gate locks (optional), and lamps (optional).

Photocell & Safety Device Guide Before connecting the photocells (or other devices) we advise you to select the type of operation according to the

Accessory manuals for most make and model accessories can be found on the web at: www.EstateSwing.com/accessories The accessory manuals you ha

The table of contents are listed to assist you locating a desired section. We do how-ever strongly suggest studying every page of the instruction manu

Marks pages with opener or usage warnings. Although we have marked these as very important warnings, please read the entire manual. Every step is impo

MODEL Estate Swing E-SC 1600 Power Supply 115V AC/ 24V AC Rated Absorbed Power (Amperage pull on a 120V AC outlet) 3 Amp/single 5 Amp/dual Max Torque

1.2 Estate Swing Parts List 1. Housing Cover 2. Column Mounting Plate 3. Manual Release Key 4. Manual Release 5. 24VDC Motor 6. Transmission Sha

Standard System Overview and Safety Zones The system display to the below is a recommended standard system. Other approved accessories can be instal

Tools Needed Other items that may be needed prior to commencing installation. • Start and stop post, bracket or door stop. Although the Estate Swing